Compression cable lugs, DIN 46235: stud hole, palm width and length, 6 to 300 mm² × M5 to M20 (+ stud-hole gauge) — dimension sheet Source: Xem Studio, https://xemstudio.com/objects/compression-cable-lugs-din-46235/ (sheet CC BY 4.0) Basis: DIN 46235 lug table (6 to 300 mm², M5 to M20, 69 rows) from a catalogue mirror, checked against HELUKABEL, Pfisterer and Schrack pages; maker differences shown; stud-hole gauge file is Xem-drawn Catalog version: 2026-10-20 Sizes: see table below - DIN 46235 compression (crimp) cable lugs: a copper tube lug with a flat palm and one hole, crimped hexagonally onto a round stranded conductor of 6 to 1000 mm² (Klauke: stud hole M5 to M20). Cross-sections here are 6 to 300 mm²; the same d1, d3 apply to every stud size of a cross-section, while d2 (the hole) depends on the stud only: M5 5.3, M6 6.4, M8 8.4, M10 10.5, M12 13, M14 15, M16 17, M20 21 mm. Both facts are checked on all 69 rows. - Source: a lug catalogue mirrored at dtsheet.com (order numbers 14978xxxxx). The copy is flattened text and the source itself warns the columns were re-aligned, so six rows were checked against independent maker pages: 240 mm² M12 at HELUKABEL agrees on all four values (hole 13, strand bore 21.5, width 42.5, length 92); Schrack 150 mm² M10: width 34, length 78, hole 10.5 (table: 34, 79, 10.5). - Makers differ by about a millimetre on b and l: Pfisterer's 10 mm² M6 lug has b 8.5, d1 4.5, d2 6.5, L 27.5 (table: b 10, d1 4.4, d2 6.4, l 27); 50 mm² M12: b 22, d1 10, d2 13, L 51 (table: b 23, d1 9.8, d2 13, l 52); 120 mm² M10: b 32, d1 15.5, d2 10.5, L 69 (table: b 31, d1 15.5, d2 10.5, l 70). DIN 46235 fixes the stud holes and strand bores; the palm width and length are maker values, so use the lug you buy for anything tighter than ±1 mm. - Column meanings: l is the length to the centre of the stud hole (HELUKABEL's legend); d is the strand-receptacle bore (HELUKABEL), here d1; the table prints a third diameter d3, which by its size (a few mm over d1) is the barrel's outside diameter. 'Not in the standard' rows (*) are the catalogue's own marking of sizes outside DIN 46235. - File: one hole gauge plate with the eight stud-hole diameters from the table. The plate size, spacing and thickness are an example, the holes are the catalogue's. Lug solids are not drawn: palm thickness, barrel length and the palm-to-barrel transition are not in any table read. - Smaller lugs for crimp terminals by stud size and AWG are on the ring-tongue page; wire ferrules for clamp terminals are on their own page. conductor cross-section, mm² bore d1 (strand), mm d3 (barrel outside Ø), mm stud stud hole d2, mm palm width b, mm length l, mm 6 3.7 5.5 M5 5.3 8.5 24 6 3.7 5.5 M6 6.4 9 24 6 3.7 5.5 M8 (not in the standard) 8.4 13 26 10 4.4 6 M5 5.3 10 27 10 4.4 6 M6 6.4 10 27 10 4.4 6 M8 8.4 13 28 10 4.4 6 M10 10.5 15 29 16 5.5 8.5 M5 (not in the standard) 5.3 13 36 16 5.5 8.5 M6 6.4 13 36 16 5.5 8.5 M8 8.4 13 37 16 5.5 8.5 M10 10.5 13 38 16 5.5 8.5 M12 (not in the standard) 13 16.5 40 25 7 10 M6 6.4 14 39 25 7 10 M8 8.4 17 39 25 7 10 M10 10.5 17 40.5 25 7 10 M12 13 18 40.5 25 7 10 M16 (not in the standard) 17 22 45 35 8.2 12.5 M6 (not in the standard) 6.4 17.5 42.5 35 8.2 12.5 M8 8.4 18 42 35 8.2 12.5 M10 10.5 20 42.5 35 8.2 12.5 M12 13 21 44 35 8.2 12.5 M16 (not in the standard) 17 28 47 50 9.8 14.5 M6 (not in the standard) 6.4 20 52 50 9.8 14.5 M8 8.4 20 52 50 9.8 14.5 M10 10.5 22 52 50 9.8 14.5 M12 13 23 52 50 9.8 14.5 M14 (not in the standard) 15 26 53.5 50 9.8 14.5 M16 17 28 55.5 50 9.8 14.5 M20 (not in the standard) 21 30 61.5 70 11.3 16.5 M8 8.4 24 56 70 11.3 16.5 M10 10.5 24 56 70 11.3 16.5 M12 13 24 56.5 70 11.3 16.5 M14 (not in the standard) 15 24 55.5 70 11.3 16.5 M16 17 29 57 70 11.3 16.5 M20 (not in the standard) 21 31 61 95 13.5 19 M8 (not in the standard) 8.4 28 65 95 13.5 19 M10 10.5 28 65.5 95 13.5 19 M12 13 28 65.5 95 13.5 19 M14 (not in the standard) 15 28 65.5 95 13.5 19 M16 17 30 65.5 95 13.5 19 M20 (not in the standard) 21 33 71 120 15.5 21 M8 (not in the standard) 8.4 31 70 120 15.5 21 M10 10.5 31 70 120 15.5 21 M12 13 31 70.5 120 15.5 21 M14 (not in the standard) 15 31 70 120 15.5 21 M16 17 31.5 70 120 15.5 21 M20 21 36 72 150 17 23.5 M8 (not in the standard) 8.4 34 79 150 17 23.5 M10 10.5 34 79 150 17 23.5 M12 13 34 78.5 150 17 23.5 M14 (not in the standard) 15 34 78 150 17 23.5 M16 17 34 78 150 17 23.5 M20 21 38 78 185 19 25.5 M8 (not in the standard) 8.4 37 83 185 19 25.5 M10 10.5 37 83 185 19 25.5 M12 13 37 82.5 185 19 25.5 M14 (not in the standard) 15 37 82 185 19 25.5 M16 17 37 82 185 19 25.5 M20 21 40 83 240 21.5 29 M10 (not in the standard) 10.5 42 92 240 21.5 29 M12 13 42.5 92 240 21.5 29 M14 (not in the standard) 15 42.5 92 240 21.5 29 M16 17 42.5 92 240 21.5 29 M20 21 45 92 300 24.5 32 M10 (not in the standard) 10.5 48.5 104 300 24.5 32 M12 (not in the standard) 13 48.5 104 300 24.5 32 M14 (not in the standard) 15 48.5 104 300 24.5 32 M16 17 48.5 100 300 24.5 32 M20 21 48.5 100 Files elsewhere (not hosted by Xem Studio; license as stated by the publisher): - dtsheet.com (catalogue mirror, order numbers 14978xxxxx): DIN 46235 tube cable lugs 6 to 300 mm2: die code, d1, d3, hole M and d2, b, l (* = not standardised); copy flattened, six rows cross-checked — web — Publisher's page; dimensions are facts — https://dtsheet.com/doc/1816621/download - HELUKABEL: Compression cable lug 240 mm2 M12 (DIN 46235 arrangement RM): hole 13, strand bore 21.5, width 42.5, length 92 — web — Publisher's page; dimensions are facts — https://shop.helukabel.com/tr-en/helu-s-pk-cu-din-m907677/906532 - Pfisterer: Cable lug DIN 46235, M6, 10 mm2: b 8.5, d1 4.5, d2 6.5, L 27.5 — web — Publisher's page; dimensions are facts — https://catalogue.pfisterer.com/en/300001001/ - Pfisterer: Cable lug DIN 46235, M12, 50 mm2: b 22, d1 10, d2 13, L 51 — web — Publisher's page; dimensions are facts — https://catalogue.pfisterer.com/en/300013015/ - Pfisterer: Cable lug DIN 46235, M10, 120 mm2: b 32, d1 15.5, d2 10.5, L 69 — web — Publisher's page; dimensions are facts — https://catalogue.pfisterer.com/en/300025359/ - Schrack Technik: Compression cable lug DIN 46235, 150 mm2 M10: width 34, length 78, hole 10.5 — web — Publisher's page; dimensions are facts — https://www.schrack.com/shop/compression-cable-lug-din-46235-150mm2-m10-xcz110r10a.html - Klauke: Compression cable lugs according to DIN 46235: 6 to 1000 mm2, stud hole M5 to M20, marking example — web — Publisher's page; dimensions are facts — https://klauke.com/pl/en/compression-cable-lugs-according-to-din-46235 Free files (CC BY 4.0, Xem Studio; STEP + STL, 1 parts): https://xemstudio.com/files/hardware/compression-cable-lugs-din-46235/index.json API: https://xemstudio.com/api/geometry?object=compression-cable-lugs-din-46235