Copper solder (sweat) fittings: nominal size to tube OD, 1/4 to 3 in, and solder coupling length (ASME B16.22 family) — dimension sheet Source: Xem Studio, https://xemstudio.com/objects/copper-solder-fittings-b16-22-sizes/ (sheet CC BY 4.0) Basis: McMaster-Carr's female solder-connect straight connector table (copper tube size, tube OD, overall length 'Lg.' as printed, two product lines), with the B16.22 and CDA table titles; numbers only. The B16.22 cup depth itself is not on this page Catalog version: 2026-10-20 Sizes: see table below - Copper solder fittings (ASME B16.22 wrought; ASME B16.18 cast) are sized by nominal copper tube size, and the tube OD is the nominal size plus 1/8 in: 1/2 in is 5/8 in (15.88 mm) OD, 3/4 in is 7/8 in (22.22 mm), 1 in is 1-1/8 in (28.58 mm). The table pairs McMaster's 'Copper Tube Size' with its 'For Tube OD' exactly as printed (and every row obeys OD = nominal + 1/8 in). The pipe itself, with its wall thickness, is on copper-pipe-type-l-m. - Coupling length. 'Lg.' is the overall length of a McMaster female solder-connect straight connector (a coupling, no centre stop) as the catalogue prints it. It is one distributor's part, not an ASME B16.22 limit: McMaster's cleaned-and-bagged line prints a different length for the three smallest sizes (3/8 → 47/64, 1/2 → 55/64, 5/8 → 1-7/64 in), so lengths differ by product line and maker. 'Lg.' is not defined on the page. - Left out on purpose: the B16.22 socket depth (cup depth, dimension G) and socket bore range (A). Table 1 of ASME B16.22 holds them, but the standard is paywalled and the free previews and CDA handbook index list the table without its values (CDA Copper Tube Handbook Table 14.9 and Figure 14.5). No manufacturer sheet read prints the socket depth either, so the cup depth is not published here and is not computed from the coupling length. Get it from the standard or from your fitting's own drawing. - Joining notes: a soldered joint needs the tube fully seated in the cup; for a push-to-connect joint see sharkbite-push-to-connect-insertion-depth (insertion depths are a maker value, measured from the fitting face). Male solder ends, elbows, tees and reducers are other McMaster tables and are not tabulated. No file: a coupling body would need the socket depth and bore, which are not published in a readable source. McMaster-Carr sells these fittings with per-part STEP; its pages are linked, not copied. copper tube size (nominal) tube OD coupling length 'Lg.' (McMaster, standard line) coupling length (McMaster, cleaned-and-bagged line) 1/4 in 3/8 in (9.52 mm) 11/16 in (17.46 mm) 47/64 in (18.65 mm) 3/8 in 1/2 in (12.7 mm) 7/8 in (22.22 mm) 55/64 in (21.83 mm) 1/2 in 5/8 in (15.88 mm) 1-1/16 in (26.99 mm) 1-7/64 in (28.18 mm) 5/8 in 3/4 in (19.05 mm) 1-5/16 in (33.34 mm) — 3/4 in 7/8 in (22.22 mm) 1-9/16 in (39.69 mm) — 1 in 1-1/8 in (28.57 mm) 1-15/16 in (49.21 mm) — 1-1/4 in 1-3/8 in (34.92 mm) 2 in (50.8 mm) — 1-1/2 in 1-5/8 in (41.27 mm) 2-1/4 in (57.15 mm) — 2 in 2-1/8 in (53.97 mm) 2-3/4 in (69.85 mm) — 2-1/2 in 2-5/8 in (66.67 mm) 3 in (76.2 mm) — 3 in 3-1/8 in (79.38 mm) 3-7/16 in (87.31 mm) — Files elsewhere (not hosted by Xem Studio; license as stated by the publisher): - McMaster-Carr: Solder-joint tube couplings (female solder-connect, copper tube sizes 1/4 to 3) (free STEP/IGES per part, for your own design use; no redistribution) — STEP, IGES, PDF — McMaster-Carr site terms: personal design use, no redistribution [verify license at link] — https://www.mcmaster.com/solder-joint-tube-couplings - McMaster-Carr: Solder-joint and socket-weld tube fittings (free STEP/IGES per part, for your own design use; no redistribution) — STEP, IGES, PDF — McMaster-Carr site terms: personal design use, no redistribution [verify license at link] — https://www.mcmaster.com/solder-joint-socket-weld-tube-fittings - ASME: B16.22 Wrought copper and copper alloy solder-joint pressure fittings: Table 1 dimensions of solder-joint ends (contents and scope only; table values are paywalled) — web — Standard store page; scope only — https://webstore.ansi.org/standards/asme/asmeb16222013 - Copper Development Association: Copper Tube Handbook: Table 14.9 'Dimensions of solder joint ends for wrought and cast pressure fittings' and Figure 14.5 (listed in the contents; values not in the text read) — web — Handbook index; scope only — https://copper.org/applications/plumbing/cth/technical-data No true-size file yet: the published figures do not fix the whole shape; a measured scan is planned. API: https://xemstudio.com/api/geometry?object=copper-solder-fittings-b16-22-sizes