# 3D printable L-rod right-angle drive: gearless 90° elbow mechanism with sliding bent rods (STL, STEP)

> How can I turn a shaft 90 degrees without gears in a 3D printed design?

- Category: Mechanisms › Couplings & joints
- Kind: Hardware
- Basis: Elbow mechanism (gearless transmission): three L-pins slide in hubs on two shafts at 90° and transmit rotation 1:1.
- Page: https://xemstudio.com/objects/l-rod-right-angle-drive/ · JSON: https://xemstudio.com/api/geometry?object=l-rod-right-angle-drive · Plain text: https://xemstudio.com/objects/l-rod-right-angle-drive/sheet.txt
- License: dimension sheet CC BY 4.0 (Xem Studio); files Xem Studio Design License (free to use and sell from, not to redistribute as files: https://xemstudio.com/license/)
- Use in every chat: add https://xemstudio.com/mcp as a connector (https://xemstudio.com/use-with-ai/)

## Overall (mm)

| length | width | height |
|---|---|---|
| 87.1 | 87.1 | 42 |

**Exact dimensions.** Every file is drawn at true size with no tolerance added. The holes and pins that meet another part are listed below under Mating features, with the fit each joint needs; open those by your process's clearance before making the part.

## Notes

- Resize: multiply every length by one factor k and the motion stays identical: angles, ratios, timing and the formulas below do not change, because a mechanism's motion depends only on the ratios of its lengths. Here, scales with k: elbow-hub, elbow-knob; stays the same: elbow-rod, elbow-frame.
- Resize: fit clearances stay in mm (a slide fit is the same gap at any size); keep every printed wall and pin at least two nozzle widths; mass grows with k³ but part strength only with k², so at k = 2 parts are about 8× heavier and 4× stronger: check pins and thin links when scaling up.
- Each rod slides in and out of its hub hole once per turn; both hubs turn at the same speed in opposite senses.
- Holes are 0.25 mm per side over the octagonal rods; rods print flat on a flat face.
- Knobs press onto the axles outside the frame; bore is nominal, add your press-fit allowance.
- Checked at 0, 30, 60 and 90°: no part collides.

## Mating features (exact size; open press / slide / run / socket by your process clearance, leave designed and clamp as drawn)

| feature | exact | mates with | fit | files |
|---|---|---|---|---|
| rod holes | Ø4.8 (rod 4 mm across flats + 0.25/side) | L-rod | run | hubs* |
| axle | Ø6 | frame hole Ø6.4 / knob bore Ø6 | run | hubs* |

## Sizes

| file | what | overall mm |
|---|---|---|
| elbow-hub | Hub: Ø30 × 14 with three Ø4.8 rod holes on R10 and a Ø6 axle | 30 × 30 × 49 |
| elbow-rod | L-rod (print 3): 4 mm octagonal legs, 39.5 mm each, 90° corner | 41.665 × 41.665 × 4.33 |
| elbow-knob | Octagonal knob, Ø6 bore for the axle | 19.753 × 19.753 × 8 |
| elbow-frame | L frame: two 4 mm walls at 90° with Ø6.4 axle holes | 78.5 × 78.5 × 42 |
| elbow-assembled | Every part in place (frame, 2 hubs, 3 rods, 2 knobs), each its own solid | 87.1 × 87.1 × 42 |

## Where the files are

- IJERT: [Design, Analysis and Fabrication of Gearless Power Transmission by using Elbow Mechanism](https://www.ijert.org/design-analysis-and-fabrication-of-gearless-power-transmission-by-using-elbow-mechanism) — web — Publisher's page; dimensions are facts
- IRJET (issuu): [Design and Fabrication of Gearless Transmission using Elbow Mechanism](https://issuu.com/irjet/docs/irjet-v8i5504) — web — Publisher's page; dimensions are facts

## Free STEP/STL (5 parts, Xem Studio Design License, Xem Studio)

Index: https://xemstudio.com/files/mechanisms/l-rod-right-angle-drive/index.json · license: https://xemstudio.com/files/mechanisms/l-rod-right-angle-drive/LICENSE.md

- elbow-hub: [STEP](https://xemstudio.com/files/mechanisms/l-rod-right-angle-drive/elbow-hub.step) · [STL](https://xemstudio.com/files/mechanisms/l-rod-right-angle-drive/elbow-hub.stl) — Hub: Ø30 × 14 with three Ø4.8 rod holes on R10 and a Ø6 axle
- elbow-rod: [STEP](https://xemstudio.com/files/mechanisms/l-rod-right-angle-drive/elbow-rod.step) · [STL](https://xemstudio.com/files/mechanisms/l-rod-right-angle-drive/elbow-rod.stl) — L-rod (print 3): 4 mm octagonal legs, 39.5 mm each, 90° corner
- elbow-knob: [STEP](https://xemstudio.com/files/mechanisms/l-rod-right-angle-drive/elbow-knob.step) · [STL](https://xemstudio.com/files/mechanisms/l-rod-right-angle-drive/elbow-knob.stl) — Octagonal knob, Ø6 bore for the axle
- elbow-frame: [STEP](https://xemstudio.com/files/mechanisms/l-rod-right-angle-drive/elbow-frame.step) · [STL](https://xemstudio.com/files/mechanisms/l-rod-right-angle-drive/elbow-frame.stl) — L frame: two 4 mm walls at 90° with Ø6.4 axle holes
- elbow-assembled: [STEP](https://xemstudio.com/files/mechanisms/l-rod-right-angle-drive/elbow-assembled.step) · [STL](https://xemstudio.com/files/mechanisms/l-rod-right-angle-drive/elbow-assembled.stl) — Every part in place (frame, 2 hubs, 3 rods, 2 knobs), each its own solid

## Questions

**How does the elbow mechanism work?**

Three L-shaped rods sit in holes in both hubs. As the input turns, each rod slides in and out and carries the output hub round with it.

**What ratio does it give?**

1:1, at 90°.

**Why three rods?**

At least three keep it turning smoothly; more rods are smoother still.

**Does it need lubrication?**

A little dry PTFE or silicone on the rods makes it much smoother.

## Fits with

- [3D printable spur gears and racks, module 2: 10–40 teeth involute gears and gear racks (STL, STEP)](https://xemstudio.com/objects/printable-spur-gears-and-racks-module-2/)
- [3D printable 45° wedge slider: converts up/down motion to left/right (cam slider, STL, STEP)](https://xemstudio.com/objects/wedge-motion-converter/)
- [Print-in-place: crank-and-slider linkage with captive pins](https://xemstudio.com/objects/print-in-place-crank-slider/)
