3D printable spur gears and racks, module 2: 10–40 teeth involute gears and gear racks (STL, STEP) — dimension sheet Source: Xem Studio, https://xemstudio.com/objects/printable-spur-gears-and-racks-module-2/ (sheet CC BY 4.0; files Xem Studio Design License, https://xemstudio.com/license/) Basis: Standard involute spur gear: module m, reference diameter m·z, centre distance (d1 + d2)/2 (KHK Gear Technical Reference). Xem design. Catalog version: 2026-10-20 Overall (mm): length 125.7, width 84, height 6 - Resize: multiply every length by one factor k and the motion stays identical: angles, ratios, timing and the formulas below do not change, because a mechanism's motion depends only on the ratios of its lengths. Here, stays the same: gear-m2-z10, gear-m2-z12, gear-m2-z15, gear-m2-z20, gear-m2-z24, gear-m2-z30, gear-m2-z40, rack-m2-10t, rack-m2-20t. - Resize: Gears scale by the module m (pitch Ø = m·z, centre distance = m·(z₁ + z₂)/2): keep the tooth counts so the ratio stays, and choose a standard module (0.5, 0.8, 1, 1.25, 1.5, 2, 2.5, 3). - Resize: fit clearances stay in mm (a slide fit is the same gap at any size); keep every printed wall and pin at least two nozzle widths; mass grows with k³ but part strength only with k², so at k = 2 parts are about 8× heavier and 4× stronger: check pins and thin links when scaling up. - Centre distance = m(z1 + z2)/2: 10+20 → 30 mm, 15+30 → 45 mm, 20+40 → 60 mm. - Rack and gear: put the gear centre m·z/2 above the rack's pitch line (the rack's pitch line is 2.5 mm above the root, 7.5 mm above its back). - Zero backlash as drawn: add 0.1–0.2 mm to the centre distance for FDM. - Print flat, 0.4 mm nozzle; module 2 teeth print cleanly without supports. file what overall mm gear-m2-z10 Module 2 spur gear, 10 teeth, pitch Ø20, outside Ø24, 6 mm face, Ø5 bore, 20° pressure angle 23.971 × 23.161 × 6 gear-m2-z12 Module 2 spur gear, 12 teeth, pitch Ø24, outside Ø28, 6 mm face, Ø5 bore, 20° pressure angle 27.972 × 27.972 × 6 gear-m2-z15 Module 2 spur gear, 15 teeth, pitch Ø30, outside Ø34, 6 mm face, Ø5 bore, 20° pressure angle 33.74 × 33.926 × 6 gear-m2-z20 Module 2 spur gear, 20 teeth, pitch Ø40, outside Ø44, 6 mm face, Ø5 bore, 20° pressure angle 43.978 × 43.978 × 6 gear-m2-z24 Module 2 spur gear, 24 teeth, pitch Ø48, outside Ø52, 6 mm face, Ø5 bore, 20° pressure angle 51.98 × 51.98 × 6 gear-m2-z30 Module 2 spur gear, 30 teeth, pitch Ø60, outside Ø64, 6 mm face, Ø5 bore, 20° pressure angle 63.983 × 63.787 × 6 gear-m2-z40 Module 2 spur gear, 40 teeth, pitch Ø80, outside Ø84, 6 mm face, Ø5 bore, 20° pressure angle 83.986 × 83.986 × 6 rack-m2-10t Module 2 rack, 10 teeth, 62.8 mm long, 6 mm face 62.832 × 9.5 × 6 rack-m2-20t Module 2 rack, 20 teeth, 125.7 mm long, 6 mm face 125.664 × 9.5 × 6 Files elsewhere (not hosted by Xem Studio; license as stated by the publisher): - KHK Gears: Gear Technical Reference — web — Publisher's page; dimensions are facts — https://khkgears.us/media/izojpong/gear_guide1.pdf - KHK Gears: Exploring the hows and whys of choosing the proper center distance — web — Publisher's page; dimensions are facts — https://www.khkgears.us/media/1215/exploring-the-hows-and-whys-of-choosing-the-proper-center-distance.pdf Free files (Xem Studio Design License, Xem Studio; STEP + STL, 9 parts): https://xemstudio.com/files/mechanisms/printable-spur-gears-and-racks-module-2/index.json API: https://xemstudio.com/api/geometry?object=printable-spur-gears-and-racks-module-2