# 3D printable ratchet wheel and pawl: one-way sawtooth wheel, plain and spring pawl (STL, STEP)

> How do I 3D print a ratchet and pawl so a wheel turns only one way?

- Category: Mechanisms › Intermittent motion
- Kind: Hardware
- Basis: Ratchet and pawl: the pawl rides over the sloped flanks one way and catches the steep face the other way; the contact normal must pass on the engagement side of the pawl pivot (FIRGELLI).
- Page: https://xemstudio.com/objects/ratchet-wheel-and-pawl/ · JSON: https://xemstudio.com/api/geometry?object=ratchet-wheel-and-pawl · Plain text: https://xemstudio.com/objects/ratchet-wheel-and-pawl/sheet.txt
- License: dimension sheet CC BY 4.0 (Xem Studio); files Xem Studio Design License (free to use and sell from, not to redistribute as files: https://xemstudio.com/license/)
- Use in every chat: add https://xemstudio.com/mcp as a connector (https://xemstudio.com/use-with-ai/)

## Overall (mm)

| length | width | height |
|---|---|---|
| 60 | 60 | 5 |

**Exact dimensions.** Every file is drawn at true size with no tolerance added. The holes and pins that meet another part are listed below under Mating features, with the fit each joint needs; open those by your process's clearance before making the part.

## Notes

- Resize: multiply every length by one factor k and the motion stays identical: angles, ratios, timing and the formulas below do not change, because a mechanism's motion depends only on the ratios of its lengths. Here, scales with k: ratchet-pawl-flex; stays the same: ratchet-wheel-od40-12t, ratchet-wheel-od60-24t, ratchet-pawl.
- Resize: fit clearances stay in mm (a slide fit is the same gap at any size); keep every printed wall and pin at least two nozzle widths; mass grows with k³ but part strength only with k², so at k = 2 parts are about 8× heavier and 4× stronger: check pins and thin links when scaling up.
- Wheel turns clockwise past the pawl, locks counter-clockwise.
- Place the pawl pivot so the pawl points along the tooth's steep face; then load pulls the pawl in.
- The flex pawl's leaf spring rests against a post or wall to keep the tip on the teeth.
- Print flat; PETG or nylon for the pawl.

## Mating features (exact size; open press / slide / run / socket by your process clearance, leave designed and clamp as drawn)

| feature | exact | mates with | fit | files |
|---|---|---|---|---|
| wheel bore | Ø5 or 6 mm square | shaft or post | run | wheels* |
| pawl pivot | Ø3 | M3 screw or 3 mm pin | run | pawls* |

## Sizes

| file | what | overall mm |
|---|---|---|
| ratchet-wheel-od40-12t | Ø40 ratchet wheel, 12 teeth 4 mm deep, Ø5 bore | 40 × 40 × 5 |
| ratchet-wheel-od60-24t | Ø60 ratchet wheel, 24 teeth, 4 spokes, 6 mm square key | 60 × 60 × 5 |
| ratchet-pawl | Pawl: 24.5 mm long, Ø3 pivot hole, pointed tip | 24.5 × 9 × 5 |
| ratchet-pawl-flex | Pawl with a printed leaf spring (1.2 mm): no separate spring needed | 32 × 16.5 × 5 |

## Where the files are

- FIRGELLI: [Pawl Mechanism Explained: Self-Locking Geometry](https://www.firgelliauto.com/en-fr/blogs/mechanisms/pawl) — web — Publisher's page; dimensions are facts
- FIRGELLI: [Ratchet-wheel Stops: Tooth Geometry and Holding Torque](https://www.firgelliauto.com/blogs/mechanisms/ratchet-wheel-stops) — web — Publisher's page; dimensions are facts

## Free STEP/STL (4 parts, Xem Studio Design License, Xem Studio)

Index: https://xemstudio.com/files/mechanisms/ratchet-wheel-and-pawl/index.json · license: https://xemstudio.com/files/mechanisms/ratchet-wheel-and-pawl/LICENSE.md

- ratchet-wheel-od40-12t: [STEP](https://xemstudio.com/files/mechanisms/ratchet-wheel-and-pawl/ratchet-wheel-od40-12t.step) · [STL](https://xemstudio.com/files/mechanisms/ratchet-wheel-and-pawl/ratchet-wheel-od40-12t.stl) — Ø40 ratchet wheel, 12 teeth 4 mm deep, Ø5 bore
- ratchet-wheel-od60-24t: [STEP](https://xemstudio.com/files/mechanisms/ratchet-wheel-and-pawl/ratchet-wheel-od60-24t.step) · [STL](https://xemstudio.com/files/mechanisms/ratchet-wheel-and-pawl/ratchet-wheel-od60-24t.stl) — Ø60 ratchet wheel, 24 teeth, 4 spokes, 6 mm square key
- ratchet-pawl: [STEP](https://xemstudio.com/files/mechanisms/ratchet-wheel-and-pawl/ratchet-pawl.step) · [STL](https://xemstudio.com/files/mechanisms/ratchet-wheel-and-pawl/ratchet-pawl.stl) — Pawl: 24.5 mm long, Ø3 pivot hole, pointed tip
- ratchet-pawl-flex: [STEP](https://xemstudio.com/files/mechanisms/ratchet-wheel-and-pawl/ratchet-pawl-flex.step) · [STL](https://xemstudio.com/files/mechanisms/ratchet-wheel-and-pawl/ratchet-pawl-flex.stl) — Pawl with a printed leaf spring (1.2 mm): no separate spring needed

## Questions

**Why does my pawl skip teeth?**

The pivot is on the wrong side: the line from the tooth contact must pass the engagement side of the pivot so load pulls the pawl in.

**Do I need a spring for the pawl?**

Use the flex pawl: its printed leaf spring presses the tip onto the teeth.

**How fine is the click?**

12 teeth click every 30°, 24 teeth every 15°.

**What is it used for?**

Winches, clickers, counters, one-way knobs and hold-open mechanisms.

## Fits with

- [3D printable spur gears and racks, module 2: 10–40 teeth involute gears and gear racks (STL, STEP)](https://xemstudio.com/objects/printable-spur-gears-and-racks-module-2/)
- [3D printable spiral torsion springs: flat clock springs with square-key hub and lever version (STL, STEP)](https://xemstudio.com/objects/printable-spiral-torsion-springs/)
- [Print-in-place: ratchet with flexible pawls (12 teeth, one-way)](https://xemstudio.com/objects/print-in-place-ratchet-flexible-pawl/)
- [3D printable bistable snap toggle: slider that clicks to either end, curved leaf springs (STL, STEP)](https://xemstudio.com/objects/bistable-snap-toggle/)
