# 3D printable rubber-band bowtie detent slider: three-position snap slider (STL, STEP)

> How do I make a 3D printed slider that clicks into fixed positions?

- Category: Mechanisms › Intermittent motion
- Kind: Hardware
- Basis: Rubber-band bowtie detent slider: designed for 3D printing, exact nominal mm.
- Page: https://xemstudio.com/objects/rubber-band-bowtie-detent-slider/ · JSON: https://xemstudio.com/api/geometry?object=rubber-band-bowtie-detent-slider · Plain text: https://xemstudio.com/objects/rubber-band-bowtie-detent-slider/sheet.txt
- License: dimension sheet CC BY 4.0 (Xem Studio); files Xem Studio Design License (free to use and sell from, not to redistribute as files: https://xemstudio.com/license/)
- Use in every chat: add https://xemstudio.com/mcp as a connector (https://xemstudio.com/use-with-ai/)

## Overall (mm)

| length | width | height |
|---|---|---|
| 100.0 | 40.0 | 12.2 |

**Exact dimensions.** Every file is drawn at true size with no tolerance added. The holes and pins that meet another part are listed below under Mating features, with the fit each joint needs; open those by your process's clearance before making the part.

## Notes

- Resize: multiply every length by one factor k and the motion stays identical: angles, ratios, timing and the formulas below do not change, because a mechanism's motion depends only on the ratios of its lengths. Here, stays the same: bowtie-slider-assembled.
- Resize: fit clearances stay in mm (a slide fit is the same gap at any size); keep every printed wall and pin at least two nozzle widths; mass grows with k³ but part strength only with k², so at k = 2 parts are about 8× heavier and 4× stronger: check pins and thin links when scaling up.
- Notches: 90 degree V, 2.5 deep, 20 mm apart; detent nose offset 0.4 mm.
- Slider 80 × 10 × 5 runs between rails with 0.4 mm gaps; the bowtie runs in a 12.8 mm guide.
- Any small rubber band works; loop it from post to post behind the bowtie's back.
- Kit: the base plate carries 5 mm pins (parts have 5.4 mm bores, 0.2 mm per side); every part prints flat on its own, and the assembled file shows them in place with 0.2 mm gaps, each part its own solid.

## Mating features (exact size; open press / slide / run / socket by your process clearance, leave designed and clamp as drawn)

| feature | exact | mates with | fit | files |
|---|---|---|---|---|
| slider in rails | 10 wide, 0.4 gap each side | base rails | run | bar* |
| detent nose | 90 degree V, 0.4 offset | slider notch | designed | detent* |

## Sizes

| file | what | overall mm |
|---|---|---|
| bowtie-slider-assembled | assembled: 3 parts in place | 100 × 40 × 12.2 |
| bowtie-slider-base | bowtie slider base | 100 × 40 × 11.2 |
| bowtie-slider-bar | bowtie slider bar | 80 × 10 × 9 |
| bowtie-detent | bowtie slider detent | 12 × 13.934 × 5 |

## Where the files are

- Wikipedia: [Detent](https://en.wikipedia.org/wiki/Detent) — web — Publisher's page; dimensions are facts
- Wikipedia: [Rubber band](https://en.wikipedia.org/wiki/Rubber_band) — web — Publisher's page; dimensions are facts

## Free STEP/STL (4 parts, Xem Studio Design License, Xem Studio)

Index: https://xemstudio.com/files/mechanisms/rubber-band-bowtie-detent-slider/index.json · license: https://xemstudio.com/files/mechanisms/rubber-band-bowtie-detent-slider/LICENSE.md

- bowtie-slider-assembled: [STEP](https://xemstudio.com/files/mechanisms/rubber-band-bowtie-detent-slider/bowtie-slider-assembled.step) · [STL](https://xemstudio.com/files/mechanisms/rubber-band-bowtie-detent-slider/bowtie-slider-assembled.stl) — bowtie slider assembly
- bowtie-slider-base: [STEP](https://xemstudio.com/files/mechanisms/rubber-band-bowtie-detent-slider/bowtie-slider-base.step) · [STL](https://xemstudio.com/files/mechanisms/rubber-band-bowtie-detent-slider/bowtie-slider-base.stl) — bowtie slider base
- bowtie-slider-bar: [STEP](https://xemstudio.com/files/mechanisms/rubber-band-bowtie-detent-slider/bowtie-slider-bar.step) · [STL](https://xemstudio.com/files/mechanisms/rubber-band-bowtie-detent-slider/bowtie-slider-bar.stl) — bowtie slider bar
- bowtie-detent: [STEP](https://xemstudio.com/files/mechanisms/rubber-band-bowtie-detent-slider/bowtie-detent.step) · [STL](https://xemstudio.com/files/mechanisms/rubber-band-bowtie-detent-slider/bowtie-detent.stl) — bowtie slider detent

## Questions

**How many stops?**

Three, 20 mm apart.

**Can I add more?**

Yes: add more V notches to the bar at any spacing over 6 mm.

**What sets the click force?**

The rubber band tension.

## Fits with

- [3D printable bistable snap toggle: slider that clicks to either end, curved leaf springs (STL, STEP)](https://xemstudio.com/objects/bistable-snap-toggle/)
- [3D printable spring-lever star-wheel ratchet indexer: 8-step index wheel with printed leaf-spring lever (STL, STEP)](https://xemstudio.com/objects/star-wheel-ratchet-indexer/)
- [3D printable flat springs: serpentine zig-zag flexure, soft, medium and firm (STL, STEP)](https://xemstudio.com/objects/flat-serpentine-springs/)
