Solid rivets: DIN 660 round head, DIN 661 countersunk (1–8 mm), ASME B18.1.1 flat, countersunk, button and truss head (1/16 to 7/16 in) — head diameter, height, shank — dimension sheet Source: Xem Studio, https://xemstudio.com/objects/solid-rivets-din-660-661-asme-b18-1-1/ (sheet CC BY 4.0) Basis: fasten.it transcriptions of DIN 660 (2012), DIN 661 (2011) and ASME B18.1.1 (1972) tables; HB Bolt's ASME flat-head cut sheet as the clean cross-check. Numbers as printed; model heads are Xem drawings from those numbers Catalog version: 2026-10-20 Sizes: see table below - DIN 660 (round head): d1 nominal shank diameter, dk nominal head diameter, k head height (js14), e max (the page defines e only by its letter), d min the smallest shank diameter. The page lists nominal lengths 2 to 40 mm (a size does not come in every length: Ø1 from 2 mm, Ø8 only from 8 mm). The 2012 edition replaced a 1993 edition with a nominal-only k; only the 2012 values are shown. - DIN 661 (countersunk, 2011): d1 min and max, dk nominal, k approximate (≈), e max, d min as printed. The cone angle is not given in the text read, so no countersunk DIN 661 model is drawn. DIN 661 dk equals DIN 660 dk for every size; k differs (it is a smaller approximate height). - ASME B18.1.1-1972, 'small solid rivets 7/16 in and smaller': the fasten.it pages print letters E (shank), A (head diameter), H (head height) and R (radius) but do not name the head type of each table. The head types here follow the table order and layout (flat, flat countersunk, button, pan, truss) in AmesWeb's version of the same standard: Table 1 has no R column and matches HB Bolt's flat-head cut sheet exactly (verified), Table 2 has an H 'ref' only and AmesWeb's note says a countersunk head is calculated on a 92° angle extended to a sharp edge, Table 3 adds R approx, Table 5 adds R1. The identification of Tables 2, 3 and 5 as countersunk, button and truss is therefore by layout, not by a label on the page. Table 4 (three radii, pan head) is not listed. - Cells left out: the countersunk 7/16 A min (the page prints '765' with no digits before it), the truss 3/8 A max / min (printed 0.808 / 0.848, which breaks the size trend), and the 1/16 row of the truss table (the table starts at 3/32). The smallest size is printed '1/6' on fasten.it; it is read as 1/16 because its basic diameter is 0.062 and HB Bolt's sheet has 1/16 at 0.062. In the truss table the shank columns have typos (0125, 0.225) and were not used; shank sizes are on the flat-head rows. The truss H cells for 7/32 and 13/32 differ from the flat-head sheet by 0.001 (0.066 / 0.145 / 0.123 against 0.065 / 0.146 / 0.124) and are shown as printed. - Recommended hole sizes are not on this page: no solid-rivet hole table (DIN or ASME) could be read in full, only a blind-rivet-mixed distributor chart, which is not used. Use the rivet shank max plus your process clearance, and confirm with your rivet supplier. - Files: 7 DIN 660 round-head rivets (Ø1, 2, 3, 4, 5, 6, 8 x 10 mm), and flat, countersunk and button heads for 1/8, 3/16, 1/4 and 3/8 in (x 1/2 in): 19 models. All shanks are plain cylinders at the nominal diameter, closed ends. Round heads are a spherical cap drawn through the published head diameter and height (DIN 660 and ASME button heads are not published as a radius, so the cap radius follows from those two numbers). Button-head caps use A max and H max, flat heads A max and H max, countersunk A max and H ref. The 10 mm and 1/2 in lengths are Xem's examples. standard size head dia (dk | A max / min) head height (k | H) e max | R shank (d min | E max / min) basic dia (ASME) DIN 660 round head (mm) 1 1.8 0.6 (js14) 0.5 d min 0.93 — DIN 660 round head (mm) 1.2 2.1 0.7 (js14) 0.6 d min 1.13 — DIN 660 round head (mm) 1.4 2.4 0.8 (js14) 0.7 d min 1.33 — DIN 660 round head (mm) 1.6 2.8 1 (js14) 0.8 d min 1.52 — DIN 660 round head (mm) 2 3.5 1.2 (js14) 1 d min 1.87 — DIN 660 round head (mm) 2.5 4.4 1.5 (js14) 1.25 d min 2.37 — DIN 660 round head (mm) 3 5.2 1.8 (js14) 1.5 d min 2.87 — DIN 660 round head (mm) 3.5 6.2 2.1 (js14) 1.75 d min 3.37 — DIN 660 round head (mm) 4 7 2.4 (js14) 2 d min 3.87 — DIN 660 round head (mm) 5 8.8 3 (js14) 2.5 d min 4.82 — DIN 660 round head (mm) 6 10.5 3.6 (js14) 3 d min 5.82 — DIN 660 round head (mm) 7 12.2 4.2 (js14) 3.5 d min 6.82 — DIN 660 round head (mm) 8 14 4.8 (js14) 4 d min 7.76 — DIN 661 countersunk (mm) 1 1.8 0.5 (approx) 0.5 d1 0.95 to 1.05; d min 0.93 — DIN 661 countersunk (mm) 1.2 2.1 0.6 (approx) 0.6 d1 1.15 to 1.25; d min 1.13 — DIN 661 countersunk (mm) 1.4 2.4 0.7 (approx) 0.7 d1 1.35 to 1.45; d min 1.33 — DIN 661 countersunk (mm) 1.6 2.8 0.8 (approx) 0.8 d1 1.55 to 1.65; d min 1.52 — DIN 661 countersunk (mm) 2 3.5 1 (approx) 1 d1 1.9 to 2.1; d min 1.87 — DIN 661 countersunk (mm) 2.5 4.4 1.2 (approx) 1.25 d1 2.4 to 2.6; d min 2.37 — DIN 661 countersunk (mm) 3 5.2 1.4 (approx) 1.5 d1 2.9 to 3.1; d min 2.87 — DIN 661 countersunk (mm) 3.5 6.2 1.8 (approx) 1.75 d1 3.4 to 3.6; d min 3.37 — DIN 661 countersunk (mm) 4 7 2 (approx) 2 d1 3.9 to 4.1; d min 3.87 — DIN 661 countersunk (mm) 5 8.8 2.5 (approx) 2.5 d1 4.85 to 5.15; d min 4.82 — DIN 661 countersunk (mm) 6 10.5 3 (approx) 3 d1 5.85 to 6.15; d min 5.82 — DIN 661 countersunk (mm) 7 12.2 3.5 (approx) 3.5 d1 6.85 to 7.15; d min 6.82 — DIN 661 countersunk (mm) 8 14 4 (approx) 4 d1 7.85 to 8.15; d min 7.76 — ASME B18.1.1 flat head (in) 1/16 A .140 / .120 H .027 / .017 — E .064 / .059 basic .062 ASME B18.1.1 flat head (in) 3/32 A .200 / .180 H .038 / .026 — E .096 / .090 basic .094 ASME B18.1.1 flat head (in) 1/8 A .260 / .240 H .048 / .036 — E .127 / .121 basic .125 ASME B18.1.1 flat head (in) 5/32 A .323 / .301 H .059 / .045 — E .158 / .152 basic .156 ASME B18.1.1 flat head (in) 3/16 A .387 / .361 H .069 / .055 — E .191 / .182 basic .188 ASME B18.1.1 flat head (in) 7/32 A .453 / .427 H .080 / .065 — E .222 / .213 basic .219 ASME B18.1.1 flat head (in) 1/4 A .515 / .485 H .091 / .075 — E .253 / .244 basic .250 ASME B18.1.1 flat head (in) 9/32 A .579 / .545 H .103 / .085 — E .285 / .273 basic .281 ASME B18.1.1 flat head (in) 5/16 A .641 / .607 H .113 / .095 — E .316 / .304 basic .312 ASME B18.1.1 flat head (in) 11/32 A .705 / .667 H .124 / .104 — E .348 / .336 basic .344 ASME B18.1.1 flat head (in) 3/8 A .769 / .731 H .135 / .115 — E .380 / .365 basic .375 ASME B18.1.1 flat head (in) 13/32 A .834 / .790 H .146 / .124 — E .411 / .396 basic .406 ASME B18.1.1 flat head (in) 7/16 A .896 / .852 H .157 / .135 — E .443 / .428 basic .438 ASME B18.1.1 flat countersunk, 92° (in) 1/16 A .118 / .110 H ref .027 — E .064 / .059 basic .062 ASME B18.1.1 flat countersunk, 92° (in) 3/32 A .176 / .163 H ref .040 — E .096 / .090 basic .094 ASME B18.1.1 flat countersunk, 92° (in) 1/8 A .235 / .217 H ref .053 — E .127 / .121 basic .125 ASME B18.1.1 flat countersunk, 92° (in) 5/32 A .293 / .272 H ref .066 — E .158 / .152 basic .156 ASME B18.1.1 flat countersunk, 92° (in) 3/16 A .351 / .326 H ref .079 — E .191 / .182 basic .188 ASME B18.1.1 flat countersunk, 92° (in) 7/32 A .413 / .384 H ref .094 — E .222 / .213 basic .219 ASME B18.1.1 flat countersunk, 92° (in) 1/4 A .469 / .437 H ref .106 — E .253 / .244 basic .250 ASME B18.1.1 flat countersunk, 92° (in) 9/32 A .528 / .491 H ref .119 — E .285 / .273 basic .281 ASME B18.1.1 flat countersunk, 92° (in) 5/16 A .588 / .547 H ref .133 — E .316 / .304 basic .312 ASME B18.1.1 flat countersunk, 92° (in) 11/32 A .646 / .602 H ref .146 — E .348 / .336 basic .344 ASME B18.1.1 flat countersunk, 92° (in) 3/8 A .704 / .656 H ref .159 — E .380 / .365 basic .375 ASME B18.1.1 flat countersunk, 92° (in) 13/32 A .763 / .710 H ref .172 — E .411 / .396 basic .406 ASME B18.1.1 flat countersunk, 92° (in) 7/16 A .823 / — H ref .186 — E .443 / .428 basic .438 ASME B18.1.1 button head (in) 1/16 A .122 / .102 H .052 / .042 R ≈ .055 E .064 / .059 basic .062 ASME B18.1.1 button head (in) 3/32 A .182 / .162 H .077 / .065 R ≈ .084 E .096 / .090 basic .094 ASME B18.1.1 button head (in) 1/8 A .235 / .215 H .100 / .088 R ≈ .111 E .127 / .121 basic .125 ASME B18.1.1 button head (in) 5/32 A .290 / .268 H .124 / .110 R ≈ .138 E .158 / .152 basic .156 ASME B18.1.1 button head (in) 3/16 A .348 / .322 H .147 / .133 R ≈ .166 E .191 / .182 basic .188 ASME B18.1.1 button head (in) 7/32 A .405 / .379 H .172 / .158 R ≈ .195 E .222 / .213 basic .219 ASME B18.1.1 button head (in) 1/4 A .460 / .430 H .196 / .180 R ≈ .221 E .253 / .244 basic .250 ASME B18.1.1 button head (in) 9/32 A .518 / .484 H .220 / .202 R ≈ .249 E .285 / .273 basic .281 ASME B18.1.1 button head (in) 5/16 A .572 / .538 H .243 / .225 R ≈ .276 E .316 / .304 basic .312 ASME B18.1.1 button head (in) 11/32 A .630 / .592 H .267 / .247 R ≈ .304 E .348 / .336 basic .344 ASME B18.1.1 button head (in) 3/8 A .684 / .646 H .291 / .271 R ≈ .332 E .380 / .365 basic .375 ASME B18.1.1 button head (in) 13/32 A .743 / .699 H .316 / .294 R ≈ .358 E .411 / .396 basic .406 ASME B18.1.1 button head (in) 7/16 A .798 / .754 H .339 / .317 R ≈ .387 E .443 / .428 basic .438 ASME B18.1.1 truss head (in) 3/32 A .226 / .206 H .038 / .026 R1 ≈ .239 see flat-head rows — ASME B18.1.1 truss head (in) 1/8 A .297 / .277 H .048 / .036 R1 ≈ .314 see flat-head rows — ASME B18.1.1 truss head (in) 5/32 A .368 / .348 H .059 / .045 R1 ≈ .392 see flat-head rows — ASME B18.1.1 truss head (in) 3/16 A .442 / .422 H .069 / .055 R1 ≈ .470 see flat-head rows — ASME B18.1.1 truss head (in) 7/32 A .515 / .495 H .080 / .066 R1 ≈ .555 see flat-head rows — ASME B18.1.1 truss head (in) 1/4 A .590 / .560 H .091 / .075 R1 ≈ .628 see flat-head rows — ASME B18.1.1 truss head (in) 9/32 A .661 / .631 H .103 / .085 R1 ≈ .706 see flat-head rows — ASME B18.1.1 truss head (in) 5/16 A .732 / .702 H .113 / .095 R1 ≈ .784 see flat-head rows — ASME B18.1.1 truss head (in) 11/32 A .806 / .776 H .124 / .104 R1 ≈ .862 see flat-head rows — ASME B18.1.1 truss head (in) 3/8 A — / — H .135 / .115 R1 ≈ .942 see flat-head rows — ASME B18.1.1 truss head (in) 13/32 A .949 / .919 H .145 / .123 R1 ≈ 1.028 see flat-head rows — ASME B18.1.1 truss head (in) 7/16 A 1.020 / .990 H .157 / .135 R1 ≈ 1.098 see flat-head rows — Files elsewhere (not hosted by Xem Studio; license as stated by the publisher): - fasten.it: DIN 660 (2012) round head rivets, nominal diameters 1 mm to 8 mm: d1, dk nom, d min, k js14, e max; masses per nominal length 2 to 40 mm — web — Reference page; numbers only; page says DIN holds the definitive text — https://fasten.it/en/norms/norm/din_660 - DIN / ANSI Webstore: DIN 660:2012 Round head rivets, nominal diameters 1 mm to 8 mm (the standard itself) — web — Standard body page; text is paywalled — https://webstore.ansi.org/standards/din/din6602012 - fasten.it: DIN 661 (2011) countersunk head rivets, 1 mm to 8 mm: d1 min / max, dk nom (h14), k approx, e max, d min — web — Reference page; numbers only; page says DIN holds the definitive text — https://fasten.it/norms/norm/din_661 - HB Bolt: Solid rivet, flat head, ANSI/ASME B18.1.1: nominal size, basic shank diameter, shank max / min, head diameter max / min, head height max / min — web — Maker cut sheet; numbers only — https://www.hbbolt.com/_Product_Cut_Sheets/SolidRivetFlatHdInfo.pdf - fasten.it: ASME B18.1.1 (1972) Table 1: small solid rivets 7/16 in and smaller (the page does not name the head type; same values as HB Bolt's flat head sheet) — web — Reference page; numbers only — https://www.fasten.it/norms/norm/asme_b18.1.1_table_1 - fasten.it: ASME B18.1.1 (1972) Table 2: small solid rivets 7/16 in and smaller (basic diameter, shank max / min, A max / min, H ref; the page does not name the head type) — web — Reference page; numbers only — https://www.fasten.it/en/norms/norm/asme_b18.1.1_table_2 - fasten.it: ASME B18.1.1 (1972) Table 3: small solid rivets 7/16 in and smaller (adds R approx; the page does not name the head type) — web — Reference page; numbers only — https://www.fasten.it/en/norms/norm/asme_b18.1.1_table_3 - fasten.it: ASME B18.1.1 (1972) Table 5: small solid rivets 3/32 to 7/16 (adds R1; the page does not name the head type; several cells have typos) — web — Reference page; numbers only — https://www.fasten.it/en/Norms/Norm/ASME_B18.1.1_TABLE_5 - AmesWeb: Solid rivet dimensions: flat, countersunk, button, pan, truss, tinners, coopers, belt (ASME B18.1.1): table layout and notes (numeric cells did not load when read) — web — Reference page; used for column layout and the 92 degree note only — https://amesweb.info/Fasteners/Rivets/Solid-Rivets-Dimensions-Flat-Countersunk-Button-Pan-Truss-Coopers-Belt.aspx - SFS (standard body store): ASME B18.1.1-1972 Small solid rivets (the standard itself) — web — Standard body page; text is paywalled — https://store.sfs.fi/en/asme-b1811-1972 Free files (CC BY 4.0, Xem Studio; STEP + STL, 19 parts): https://xemstudio.com/files/hardware/solid-rivets-din-660-661-asme-b18-1-1/index.json API: https://xemstudio.com/api/geometry?object=solid-rivets-din-660-661-asme-b18-1-1