# 3D printable spiral-spring clicker: push-button snap clicker with a printed clock spring (STL, STEP)

> How do I make a 3D printed clicker with a printed spring?

- Category: Mechanisms › Mechanism parts
- Kind: Hardware
- Basis: Spiral-spring clicker: designed for 3D printing, exact nominal mm.
- Page: https://xemstudio.com/objects/spiral-spring-clicker/ · JSON: https://xemstudio.com/api/geometry?object=spiral-spring-clicker · Plain text: https://xemstudio.com/objects/spiral-spring-clicker/sheet.txt
- License: dimension sheet CC BY 4.0 (Xem Studio); files Xem Studio Design License (free to use and sell from, not to redistribute as files: https://xemstudio.com/license/)
- Use in every chat: add https://xemstudio.com/mcp as a connector (https://xemstudio.com/use-with-ai/)

## Overall (mm)

| length | width | height |
|---|---|---|
| 84.0 | 68.0 | 9.7 |

**Exact dimensions.** Every file is drawn at true size with no tolerance added. The holes and pins that meet another part are listed below under Mating features, with the fit each joint needs; open those by your process's clearance before making the part.

## Notes

- Resize: multiply every length by one factor k and the motion stays identical: angles, ratios, timing and the formulas below do not change, because a mechanism's motion depends only on the ratios of its lengths. Here, step to the nearest standard size (and redraw the hole or pocket it fits): spring-clicker-assembled, spring-clicker-base, spring-clicker-spring, spring-clicker-button.
- Resize: fit clearances stay in mm (a slide fit is the same gap at any size); keep every printed wall and pin at least two nozzle widths; mass grows with k³ but part strength only with k², so at k = 2 parts are about 8× heavier and 4× stronger: check pins and thin links when scaling up.
- Spring: spiral_spring OD 40, 1.0 mm arms, 1.5 turns, 30 mm lever; hub keys on a 4.6 mm square post.
- Button runs between rails and lifts the lever at 35 mm from the centre.
- Lever tip rests 0.3 mm off the 5 mm stop post.
- Kit: the base plate carries 5 mm pins (parts have 5.4 mm bores, 0.2 mm per side); every part prints flat on its own, and the assembled file shows them in place with 0.2 mm gaps, each part its own solid.

## Mating features (exact size; open press / slide / run / socket by your process clearance, leave designed and clamp as drawn)

| feature | exact | mates with | fit | files |
|---|---|---|---|---|
| spring hub | 5.0 square hole | 4.6 square post | slide | spring* |
| button in rails | 8 wide, 0.4 gap each side | base rails | run | button* |

## Sizes

| file | what | overall mm |
|---|---|---|
| spring-clicker-assembled | assembled: 3 parts in place | 84 × 68 × 9.7 |
| spring-clicker-base | spring clicker base | 84 × 68 × 9.7 |
| spring-clicker-spring | spring clicker spring | 72.5 × 40 × 5 |
| spring-clicker-button | spring clicker button | 12 × 37 × 5 |

## Where the files are

- Wikipedia: [Spring (device)](https://en.wikipedia.org/wiki/Spring_(device)) — web — Publisher's page; dimensions are facts
- Wikipedia: [Clicker](https://en.wikipedia.org/wiki/Clicker) — web — Publisher's page; dimensions are facts

## Free STEP/STL (4 parts, Xem Studio Design License, Xem Studio)

Index: https://xemstudio.com/files/mechanisms/spiral-spring-clicker/index.json · license: https://xemstudio.com/files/mechanisms/spiral-spring-clicker/LICENSE.md

- spring-clicker-assembled: [STEP](https://xemstudio.com/files/mechanisms/spiral-spring-clicker/spring-clicker-assembled.step) · [STL](https://xemstudio.com/files/mechanisms/spiral-spring-clicker/spring-clicker-assembled.stl) — spring clicker assembly
- spring-clicker-base: [STEP](https://xemstudio.com/files/mechanisms/spiral-spring-clicker/spring-clicker-base.step) · [STL](https://xemstudio.com/files/mechanisms/spiral-spring-clicker/spring-clicker-base.stl) — spring clicker base
- spring-clicker-spring: [STEP](https://xemstudio.com/files/mechanisms/spiral-spring-clicker/spring-clicker-spring.step) · [STL](https://xemstudio.com/files/mechanisms/spiral-spring-clicker/spring-clicker-spring.stl) — spring clicker spring
- spring-clicker-button: [STEP](https://xemstudio.com/files/mechanisms/spiral-spring-clicker/spring-clicker-button.step) · [STL](https://xemstudio.com/files/mechanisms/spiral-spring-clicker/spring-clicker-button.stl) — spring clicker button

## Questions

**What makes the click?**

The spring lever snapping back onto the stop post.

**Can I make it louder?**

Use thicker spring arms (1.2–1.4 mm) or a thinner stop post that rings.

## Fits with

- [3D printable spiral torsion springs: flat clock springs with square-key hub and lever version (STL, STEP)](https://xemstudio.com/objects/printable-spiral-torsion-springs/)
- [3D printable bistable snap toggle: slider that clicks to either end, curved leaf springs (STL, STEP)](https://xemstudio.com/objects/bistable-snap-toggle/)
