Library › Mechanisms › Gears ·

3D printable gear-sector amplifier: 6:1 sector-and-pinion pointer mechanism (STL, STEP)

How do I amplify a small rotation with a gear sector and pinion? · Hardware · basis: Gear-sector amplifier: designed for 3D printing, exact nominal mm.

Also called: sector gear amplifier, segment gear and pinion, motion amplifier mechanism, pointer amplifier, dial gauge mechanism 3d print

Exact dimensions. Every file is drawn at true size with no tolerance added. The holes and pins that meet another part are listed below under Mating features, with the fit each joint needs; open those by your process's clearance before making the part. Mating features

length
159.3 mm
width
92.0 mm
height
12.2 mm

Notes

  • Resize: multiply every length by one factor k and the motion stays identical: angles, ratios, timing and the formulas below do not change, because a mechanism's motion depends only on the ratios of its lengths. Here, stays the same: sector-amp-assembled.
  • Resize: Gears scale by the module m (pitch Ø = m·z, centre distance = m·(z₁ + z₂)/2): keep the tooth counts so the ratio stays, and choose a standard module (0.5, 0.8, 1, 1.25, 1.5, 2, 2.5, 3).
  • Resize: fit clearances stay in mm (a slide fit is the same gap at any size); keep every printed wall and pin at least two nozzle widths; mass grows with k³ but part strength only with k², so at k = 2 parts are about 8× heavier and 4× stronger: check pins and thin links when scaling up.
  • Ratio 72:12 = 6:1; centre distance 63.3 (63 nominal + 0.3 backlash).
  • Sector teeth span 50 degrees; stop pins limit the lever to about ±12 degrees so it never runs out of mesh.
  • Pointer keys on the pinion's 8 mm square boss (8.4 mm hole).
  • Kit: the base plate carries 5 mm pins (parts have 5.4 mm bores, 0.2 mm per side); every part prints flat on its own, and the assembled file shows them in place with 0.2 mm gaps, each part its own solid.

3D printable gear-sector amplifier: 6:1 sector-and-pinion pointer… size chart

filewhatoverall mm
sector-amp-assembledassembled: 4 parts in place159.3 × 92 × 12.2
sector-amp-basesector amp base159.3 × 92 × 12.2
sector-amp-sectorsector amp sector97.497 × 46.908 × 5
sector-amp-pinionsector amp pinion20.979 × 20.979 × 9
sector-amp-pointersector amp pointer47 × 14 × 2

Mating features

Drawn at the exact size. Open press, slide, run and socket features by your process's clearance (tolerances by process); leave designed gaps and clamp fits as drawn.

featureexactmates withfitfiles
meshmodule 1.5, 72:12sector and piniondesignedgears*
pointer8.4 square hole8 square bossslidepointer*

Where the files are

Other publishers' files are linked, not hosted. "verify" = check the license at the link before commercial use.

WikipediaGearwebPublisher's page; dimensions are facts
WikipediaIndicator (distance amplifying instrument)webPublisher's page; dimensions are facts

Free files

★ Free files 5 parts. Xem Studio design: free to use, print and sell things from; not to be republished as files. Xem Studio Design License. index.json

Use this part in your AI. Your AI gets the exact sizes and files straight from Xem and can design a mount, case or adapter around it. Direct downloads here are limited to one file every 10 minutes; through your AI they are unlimited.

Connect Xem to your AI (free, no account, about a minute)
https://xemstudio.com/mcp
  1. Claude: Add to Claude
  2. ChatGPT (Plus or higher): open Connectors → Advanced → turn on Developer mode → Create → paste the address, no authentication → Create.
  3. Cursor: install with one click. VS Code: install with one click.
Other apps and full steps
sector-amp-assembledsector amp assemblySTEP · STL
sector-amp-basesector amp baseSTEP · STL
sector-amp-sectorsector amp sectorSTEP · STL
sector-amp-pinionsector amp pinionSTEP · STL
sector-amp-pointersector amp pointerSTEP · STL
Let your AI pull this. Claude: add Xem in one click. ChatGPT, Cursor or any MCP client: add https://xemstudio.com/mcp (free, no account). Your AI can then look up exact sizes, mating fits and free STEP/STL from every chat.
Set it up →

Plain text: sheet.txt · JSON: /api/geometry?object=gear-sector-amplifier

3D printable gear-sector amplifier: 6:1 sector-and-pinion pointer mechanism (STL, STEP), isometric render of a generated part
Render of sector-amp-assembled from the free STEP; not to scale.

Fits with

Questions

What is the ratio?

6:1: sector 72-tooth pitch circle, pinion 12 teeth.

Why a sector, not a full gear?

Only a small arc of teeth is ever used, so the rest is cut away.

Can I change the ratio?

Yes, with a different pinion; keep centre distance = 1.5 × (72 + z) / 2 + 0.3.