Xem Studiomeasured geometryLibrary › Hardware › Knobs, handles & feet ·
Leveling feet: base diameter and stud thread (Ganter GN 343.1 / 343.2 Ø25–60, M6–M24; Ganter and McMaster-Carr option ranges)
What thread and base diameter do leveling feet come in, and which thread goes with which foot size? · Standard part · basis: The foot diameter d1 and thread set per d1 from Ganter's GN 343.1 / 343.2 datasheet (as hosted by Dold), plus the filter ranges of Ganter's leveling foot category and McMaster-Carr's metric leveling foot page; option lists are not per-part rows
Also called: GN 343 leveling feet, leveling foot M10, adjustable foot thread, machine leveling feet sizes, levelling foot M8 base diameter, threaded leveling foot, Stellfuß GN 343, leveling feet thread size chart, M12 leveling foot
Exact dimensions. Every file is drawn at true size with no tolerance added. The holes and pins that meet another part are listed below under Mating features, with the fit each joint needs; open those by your process's clearance before making the part. Mating features
- sizes
- 7 in table
Notes
- GN 343.1 / 343.2 (steel leveling foot with internal thread socket or threaded stud): the datasheet's d1 column is the foot diameter, 25, 32, 40, 50 and 60, and each d1 comes with the thread sizes shown (d2). It also prints stud lengths l1 to l5, a spanner width, a static load capacity (7.5 to 95 kN) and two further columns that are not labelled; the machine reading could not tell which thread column belongs to the socket version and which to the stud version, and the load column is headed as GN 343.2 only while a note says it applies to certain forms. These columns are therefore not tabulated here: use Ganter's drawing for stud length, spanner width and load. The thread sets above are the union of the two thread columns per d1.
- McMaster-Carr rows are option lists from its metric leveling feet page, not per-part rows: thread sizes M3 to M48 and 1/4-20, base diameters 19 mm to 152 mm and 1-1/4 to 5-7/8 in, stud lengths 6 to 37 mm, overall heights 13 to 48 mm. The page does not say which values go together. Ganter's category page lists the families (GN 343.x steel / stainless; 344, 345 plastic; 638 ball-jointed; 339, 839 screw-type; 440 with rubber cap; 17 to 24 hygienic; 42, 43, 45 with fixing lugs; 30 to 33 rubber pad; 36, 37 machine feet; 244 to 247) with filter ranges: foot Ø 14 to 200, thread M4 to M44 x 2, stud length 14 to 300.
- Furniture leg caps and risers are on furniture-leg-caps-40mm; extrusion end feet on t-slot-feet. No file: the foot and base shapes are not given as numbers in the sources used. McMaster-Carr sells leveling feet and equipment feet with per-part STEP; linked, not copied.
Leveling feet: base diameter and stud thread size chart
| source | base / foot diameter d1 | thread | stud length | overall height | capacity |
|---|---|---|---|---|---|
| Ganter GN 343.1 / 343.2 (d1 | threads offered) | 25 | M6, M8, M10 | — | — | — |
| Ganter GN 343.1 / 343.2 (d1 | threads offered) | 32 | M8, M10, M12 | — | — | — |
| Ganter GN 343.1 / 343.2 (d1 | threads offered) | 40 | M8, M10, M12 | — | — | — |
| Ganter GN 343.1 / 343.2 (d1 | threads offered) | 50 | M8, M10, M12, M16 | — | — | — |
| Ganter GN 343.1 / 343.2 (d1 | threads offered) | 60 | M10, M12, M16, M20, M24 | — | — | — |
| McMaster-Carr metric leveling feet (option lists) | base Ø: 19, 25, 25.4, 30, 32, 48, 50, 51, 52, 60, 61, 64, 71, 76, 80, 81, 102, 109, 127, 152 mm; 1-1/4, 1-5/16, 1-1/2, 2, 2-17/32, 2-9/16, 2-5/8, 3, 3-1/8, 3-3/16, 3-7/8, 5, 5-1/2, 5-7/8 in | M3, M4, M5, M6, M8, M10, M12, M16, M20, M24, M30, M36, M42, M48; 1/4-20 | stud length: 6, 8, 10, 12, 13, 15, 16, 18, 20, 23, 25, 27, 28, 29, 30, 32, 34, 37 mm | overall height: 13, 14, 16, 17, 20, 22, 25, 29, 32, 34, 35, 38, 39, 41, 45, 46, 47, 48 mm | capacity per mount bins: under 10,000 lb up to 40,000 lb and over |
| Ganter leveling foot range (filters) | foot Ø 14 to 200 | M4 to M44 x 2 | stud length 14 to 300 | — | — |
Mating features
Drawn at the exact size. Open press, slide, run and socket features by your process's clearance (tolerances by process); leave designed gaps and clamp fits as drawn.
| feature | exact | mates with | fit | files |
|---|---|---|---|---|
| stud / socket thread d2 | M6 to M24 by foot diameter (see table) | tapped hole or threaded stud of the same metric thread in the machine frame | designed | all |
Where the files are
Other publishers' files are linked, not hosted. "verify" = check the license at the link before commercial use.
| Elesa+Ganter (via the JW Winco / Dold datasheet) | GN 343.1 / 343.2 leveling feet: d1 foot diameter 25 to 60 and the threads d2 offered per size (M6 to M24); other columns not used because several are unlabelled | web | Maker datasheet; used for d1 and the thread set per d1 only |
| Ganter | Leveling feet range: filter ranges foot diameter 14 to 200, thread M4 to M44 x 2, stud length 14 to 300; families GN 343, 344, 345, 638, 339, 440 and others | web | Maker category page; ranges only |
| McMaster-Carr | Metric leveling feet (free STEP/IGES per part, for your own design use; no redistribution) | STEP, IGES, PDF | McMaster-Carr site terms: personal design use, no redistribution verify |
| McMaster-Carr | Equipment feet (free STEP/IGES per part, for your own design use; no redistribution) | STEP, IGES, PDF | McMaster-Carr site terms: personal design use, no redistribution verify |
Xem scan
File coming
No downloadable true-size file yet: the published figures do not fix the whole shape, and Xem never guesses a number. A measured scan is planned; request it and it moves up.
https://xemstudio.com/mcp to Claude, ChatGPT, Cursor or any MCP client (free, no account, one minute) and it can look up exact sizes, mating fits and free STEP/STL from every chat.Plain text: sheet.txt · JSON: /api/geometry?object=leveling-feet-gn-343-and-mcmaster
Fits with
Questions
Which threads does a Ø40 GN 343 foot have?
M8, M10 or M12 (d2) on the Ganter datasheet; Ø25 has M6, M8, M10 and Ø60 has M10 to M24.
What thread sizes does McMaster-Carr list for metric leveling feet?
M3, M4, M5, M6, M8, M10, M12, M16, M20, M24, M30, M36, M42, M48 and 1/4-20.
Is there a foot with Ø80?
McMaster lists a base diameter of 80 mm in its options; Ganter's GN 343 sheet used here stops at Ø60 (the category goes to Ø200).