Library › 3D printing › Snap fits & clips ·

3D printable bistable snap toggle: slider that clicks to either end, curved leaf springs (STL, STEP)

Is there a 3D printable mechanism that snaps a slider to one of two positions and holds it there? · Hardware · basis: Bistable compliant mechanism: two pre-curved leaf springs give two stable slider positions with an energy peak between them (BYU compliant mechanisms research). Xem design.

Also called: bistable toggle 3d print, snap through mechanism, detent slider stl, two position latch, leaf spring detent, compliant bistable switch, printable click slider, flexure toggle mechanism

Exact dimensions. Every file is drawn at true size with no tolerance added. The holes and pins that meet another part are listed below under Mating features, with the fit each joint needs; open those by your process's clearance before making the part. Mating features

length
136.5 mm
width
60.0 mm
height
7.25 mm

Notes

  • The slider rests at either end. Pushing it toward the middle forces the boss between the two leaf springs, which bend outward; past centre they push it on to the other end with a click.
  • Leaves are printed in their installed shape and drop over the posts by their end rings. The boss bends each leaf 2.4 mm (50 × 40) or 3.5 mm (75 × 60) at the middle.
  • Print the leaves in PETG or nylon, 3 mm tall, flat on the bed; PLA leaves crack after repeated flexing. Frame, cover and slider in any material.
  • 0.3 mm clearance is built in: slider in its slots, leaf rings on the posts, parts in the 3.6 mm cavity. Assemble with four M3 × 8 self-tapping screws through the cover into the posts.

3D printable bistable snap toggle: slider that clicks to either end… size chart

part50 × 40 size mm75 × 60 size mmqty
frame50 × 40 × 5.675 × 60 × 5.61
cover50 × 40 × 1.675 × 60 × 1.61
slider (bar + boss)91 × 6 × 3, boss Ø12136.5 × 9 × 3, boss Ø181
leaf spring0.8 thick × 3 tall, 36 span, 8 sag0.98 thick × 3 tall, 54 span, 12 sag2
slider travel±16.5±24.75—
screwsM3 × 8 self-tappingM3 × 8 self-tapping4

Mating features

Drawn at the exact size. Open press, slide, run and socket features by your process's clearance (tolerances by process); leave designed gaps and clamp fits as drawn.

featureexactmates withfitfiles
slider in end-wall slotsbar + 0.6 mmframe slotsrunall
leaf end ringspost Ø5 + 0.6 mmframe postsrunall
screw holes2.5 mm pilot / 3.2 mm clearanceM3 self-tapping screwdesignedall

Where the files are

Other publishers' files are linked, not hosted. "verify" = check the license at the link before commercial use.

BYU Compliant Mechanisms Research GroupCompliant Mechanisms ExplainedwebPublisher's page; dimensions are facts
BYU ScholarsArchiveJensen, B. D., Identification of Macro- and Micro-Compliant Mechanism Configurations Resulting in Bistable BehaviorwebPublisher's page; dimensions are facts

Free files

★ Free files 10 parts. Xem Studio design: free to use, print and sell things from; not to be republished as files. Xem Studio Design License. index.json

Use this part in your AI. Your AI gets the exact sizes and files straight from Xem and can design a mount, case or adapter around it. Direct downloads here are limited to one file every 10 minutes; through your AI they are unlimited.

Connect Xem to your AI (free, no account, about a minute)
https://xemstudio.com/mcp
  1. Claude: Add to Claude
  2. ChatGPT (Plus or higher): open Connectors → Advanced → turn on Developer mode → Create → paste the address, no authentication → Create.
  3. Cursor: install with one click. VS Code: install with one click.
Other apps and full steps
toggle-50x40-frame50x40 mm: Base frame: 2 mm plate with sight window, perimeter wall with slider slots at both ends, four posts with 2.5 mm pilot holes for M3 self-tapping screwsSTEP · STL
toggle-50x40-cover50x40 mm: Cover plate: same outline and window, four 3.2 mm screw clearance holes, 1.6 mm thickSTEP · STL
toggle-50x40-slider50x40 mm: Slider: flat bar with a round boss at its middle that squeezes past the leaf springsSTEP · STL
toggle-50x40-leaf50x40 mm: Leaf spring: thin arc from post to post with a ring at each end; PETG or nylonSTEP · STL
toggle-50x40-assembled50x40 mm: All parts in place, cover closed, slider resting at one end (each part its own solid)STEP · STL
toggle-75x60-frame75x60 mm: Base frame: 2 mm plate with sight window, perimeter wall with slider slots at both ends, four posts with 2.5 mm pilot holes for M3 self-tapping screwsSTEP · STL
toggle-75x60-cover75x60 mm: Cover plate: same outline and window, four 3.2 mm screw clearance holes, 1.6 mm thickSTEP · STL
toggle-75x60-slider75x60 mm: Slider: flat bar with a round boss at its middle that squeezes past the leaf springsSTEP · STL
toggle-75x60-leaf75x60 mm: Leaf spring: thin arc from post to post with a ring at each end; PETG or nylonSTEP · STL
toggle-75x60-assembled75x60 mm: All parts in place, cover closed, slider resting at one end (each part its own solid)STEP · STL
Let your AI pull this. Claude: add Xem in one click. ChatGPT, Cursor or any MCP client: add https://xemstudio.com/mcp (free, no account). Your AI can then look up exact sizes, mating fits and free STEP/STL from every chat.
Set it up →

Plain text: sheet.txt · JSON: /api/geometry?object=bistable-snap-toggle

3D printable bistable snap toggle: slider that clicks to either end, curved leaf springs (STL, STEP), isometric render of a generated part
Render of toggle-50x40-assembled from the free STEP; not to scale.

Fits with

Questions

What is a bistable mechanism?

One with two resting positions and a hump of stored spring energy between them, so it snaps to one or the other and holds there without power.

How does this toggle work?

The slider's round boss must push two curved leaf springs apart to pass the middle. Before centre they push it back; past centre they push it on to the other end.

What filament should the springs be?

PETG or nylon. They bend every click; PLA leaves crack after a while.

Can I make it snap harder or softer?

Use the 75 × 60 size for a longer stroke, or scale leaf thickness: stiffness rises with thickness cubed.

What can I use it for?

Two-position latches, mode switches, detents, lid stays, fidget toys, or any slider that must stay put at its ends.