Library › Mechanisms › Intermittent motion ·

3D printable ratchet wheel and pawl: one-way sawtooth wheel, plain and spring pawl (STL, STEP)

How do I 3D print a ratchet and pawl so a wheel turns only one way? · Hardware · basis: Ratchet and pawl: the pawl rides over the sloped flanks one way and catches the steep face the other way; the contact normal must pass on the engagement side of the pawl pivot (FIRGELLI).

Also called: 3d printable ratchet, ratchet and pawl stl, printable pawl, one way wheel 3d print, ratchet gear stl

Exact dimensions. Every file is drawn at true size with no tolerance added. The holes and pins that meet another part are listed below under Mating features, with the fit each joint needs; open those by your process's clearance before making the part. Mating features

length
60 mm
width
60 mm
height
5 mm

Notes

  • Resize: multiply every length by one factor k and the motion stays identical: angles, ratios, timing and the formulas below do not change, because a mechanism's motion depends only on the ratios of its lengths. Here, scales with k: ratchet-pawl-flex; stays the same: ratchet-wheel-od40-12t, ratchet-wheel-od60-24t, ratchet-pawl.
  • Resize: fit clearances stay in mm (a slide fit is the same gap at any size); keep every printed wall and pin at least two nozzle widths; mass grows with k³ but part strength only with k², so at k = 2 parts are about 8× heavier and 4× stronger: check pins and thin links when scaling up.
  • Wheel turns clockwise past the pawl, locks counter-clockwise.
  • Place the pawl pivot so the pawl points along the tooth's steep face; then load pulls the pawl in.
  • The flex pawl's leaf spring rests against a post or wall to keep the tip on the teeth.
  • Print flat; PETG or nylon for the pawl.

3D printable ratchet wheel and pawl: one-way sawtooth wheel, plain… size chart

filewhatoverall mm
ratchet-wheel-od40-12tØ40 ratchet wheel, 12 teeth 4 mm deep, Ø5 bore40 × 40 × 5
ratchet-wheel-od60-24tØ60 ratchet wheel, 24 teeth, 4 spokes, 6 mm square key60 × 60 × 5
ratchet-pawlPawl: 24.5 mm long, Ø3 pivot hole, pointed tip24.5 × 9 × 5
ratchet-pawl-flexPawl with a printed leaf spring (1.2 mm): no separate spring needed32 × 16.5 × 5

Mating features

Drawn at the exact size. Open press, slide, run and socket features by your process's clearance (tolerances by process); leave designed gaps and clamp fits as drawn.

featureexactmates withfitfiles
wheel boreØ5 or 6 mm squareshaft or postrunwheels*
pawl pivotØ3M3 screw or 3 mm pinrunpawls*

Where the files are

Other publishers' files are linked, not hosted. "verify" = check the license at the link before commercial use.

FIRGELLIPawl Mechanism Explained: Self-Locking GeometrywebPublisher's page; dimensions are facts
FIRGELLIRatchet-wheel Stops: Tooth Geometry and Holding TorquewebPublisher's page; dimensions are facts

Free files

★ Free files 4 parts. Xem Studio design: free to use, print and sell things from; not to be republished as files. Xem Studio Design License. index.json

Use this part in your AI. Your AI gets the exact sizes and files straight from Xem and can design a mount, case or adapter around it. Direct downloads here are limited to one file every 10 minutes; through your AI they are unlimited.

Connect Xem to your AI (free, no account, about a minute)
https://xemstudio.com/mcp
  1. Claude: Add to Claude
  2. ChatGPT (Plus or higher): open Connectors → Advanced → turn on Developer mode → Create → paste the address, no authentication → Create.
  3. Cursor: install with one click. VS Code: install with one click.
Other apps and full steps
ratchet-wheel-od40-12tØ40 ratchet wheel, 12 teeth 4 mm deep, Ø5 boreSTEP · STL
ratchet-wheel-od60-24tØ60 ratchet wheel, 24 teeth, 4 spokes, 6 mm square keySTEP · STL
ratchet-pawlPawl: 24.5 mm long, Ø3 pivot hole, pointed tipSTEP · STL
ratchet-pawl-flexPawl with a printed leaf spring (1.2 mm): no separate spring neededSTEP · STL
Let your AI pull this. Claude: add Xem in one click. ChatGPT, Cursor or any MCP client: add https://xemstudio.com/mcp (free, no account). Your AI can then look up exact sizes, mating fits and free STEP/STL from every chat.
Set it up →

Plain text: sheet.txt · JSON: /api/geometry?object=ratchet-wheel-and-pawl

3D printable ratchet wheel and pawl: one-way sawtooth wheel, plain and spring pawl (STL, STEP), isometric render of a generated part
Render of ratchet-wheel-od60-24t from the free STEP; not to scale.

Fits with

Questions

Why does my pawl skip teeth?

The pivot is on the wrong side: the line from the tooth contact must pass the engagement side of the pivot so load pulls the pawl in.

Do I need a spring for the pawl?

Use the flex pawl: its printed leaf spring presses the tip onto the teeth.

How fine is the click?

12 teeth click every 30°, 24 teeth every 15°.

What is it used for?

Winches, clickers, counters, one-way knobs and hold-open mechanisms.