Library › Mechanisms › Mechanism parts ·
3D printable spiral-spring clicker: push-button snap clicker with a printed clock spring (STL, STEP)
How do I make a 3D printed clicker with a printed spring? · Hardware · basis: Spiral-spring clicker: designed for 3D printing, exact nominal mm.
Also called: spring clicker, 3d printed clicker, spiral spring toy, clock spring clicker, fidget clicker mechanism
Exact dimensions. Every file is drawn at true size with no tolerance added. The holes and pins that meet another part are listed below under Mating features, with the fit each joint needs; open those by your process's clearance before making the part. Mating features
- length
- 84.0 mm
- width
- 68.0 mm
- height
- 9.7 mm
Notes
- Resize: multiply every length by one factor k and the motion stays identical: angles, ratios, timing and the formulas below do not change, because a mechanism's motion depends only on the ratios of its lengths. Here, step to the nearest standard size (and redraw the hole or pocket it fits): spring-clicker-assembled, spring-clicker-base, spring-clicker-spring, spring-clicker-button.
- Resize: fit clearances stay in mm (a slide fit is the same gap at any size); keep every printed wall and pin at least two nozzle widths; mass grows with k³ but part strength only with k², so at k = 2 parts are about 8× heavier and 4× stronger: check pins and thin links when scaling up.
- Spring: spiral_spring OD 40, 1.0 mm arms, 1.5 turns, 30 mm lever; hub keys on a 4.6 mm square post.
- Button runs between rails and lifts the lever at 35 mm from the centre.
- Lever tip rests 0.3 mm off the 5 mm stop post.
- Kit: the base plate carries 5 mm pins (parts have 5.4 mm bores, 0.2 mm per side); every part prints flat on its own, and the assembled file shows them in place with 0.2 mm gaps, each part its own solid.
3D printable spiral-spring clicker: push-button snap clicker with a… size chart
| file | what | overall mm |
|---|---|---|
| spring-clicker-assembled | assembled: 3 parts in place | 84 × 68 × 9.7 |
| spring-clicker-base | spring clicker base | 84 × 68 × 9.7 |
| spring-clicker-spring | spring clicker spring | 72.5 × 40 × 5 |
| spring-clicker-button | spring clicker button | 12 × 37 × 5 |
Mating features
Drawn at the exact size. Open press, slide, run and socket features by your process's clearance (tolerances by process); leave designed gaps and clamp fits as drawn.
| feature | exact | mates with | fit | files |
|---|---|---|---|---|
| spring hub | 5.0 square hole | 4.6 square post | slide | spring* |
| button in rails | 8 wide, 0.4 gap each side | base rails | run | button* |
Where the files are
Other publishers' files are linked, not hosted. "verify" = check the license at the link before commercial use.
| Wikipedia | Spring (device) | web | Publisher's page; dimensions are facts |
| Wikipedia | Clicker | web | Publisher's page; dimensions are facts |
Free files
★ Free files 4 parts. Xem Studio design: free to use, print and sell things from; not to be republished as files. Xem Studio Design License. index.json
Use this part in your AI. Your AI gets the exact sizes and files straight from Xem and can design a mount, case or adapter around it. Direct downloads here are limited to one file every 10 minutes; through your AI they are unlimited.
Connect Xem to your AI (free, no account, about a minute)
https://xemstudio.com/mcp- Claude: Add to Claude
- ChatGPT (Plus or higher): open Connectors → Advanced → turn on Developer mode → Create → paste the address, no authentication → Create.
- Cursor: install with one click. VS Code: install with one click.
| spring-clicker-assembled | spring clicker assembly | STEP · STL |
| spring-clicker-base | spring clicker base | STEP · STL |
| spring-clicker-spring | spring clicker spring | STEP · STL |
| spring-clicker-button | spring clicker button | STEP · STL |
https://xemstudio.com/mcp (free, no account). Your AI can then look up exact sizes, mating fits and free STEP/STL from every chat.Plain text: sheet.txt · JSON: /api/geometry?object=spiral-spring-clicker

Fits with
Questions
What makes the click?
The spring lever snapping back onto the stop post.
Can I make it louder?
Use thicker spring arms (1.2–1.4 mm) or a thinner stop post that rings.

