Library › Mechanisms › Intermittent motion ·

3D printable rubber-band bowtie detent slider: three-position snap slider (STL, STEP)

How do I make a 3D printed slider that clicks into fixed positions? · Hardware · basis: Rubber-band bowtie detent slider: designed for 3D printing, exact nominal mm.

Also called: bowtie detent, rubber band detent slider, 3 position slider detent, printed detent mechanism, slider with click stops

Exact dimensions. Every file is drawn at true size with no tolerance added. The holes and pins that meet another part are listed below under Mating features, with the fit each joint needs; open those by your process's clearance before making the part. Mating features

length
100.0 mm
width
40.0 mm
height
12.2 mm

Notes

  • Resize: multiply every length by one factor k and the motion stays identical: angles, ratios, timing and the formulas below do not change, because a mechanism's motion depends only on the ratios of its lengths. Here, stays the same: bowtie-slider-assembled.
  • Resize: fit clearances stay in mm (a slide fit is the same gap at any size); keep every printed wall and pin at least two nozzle widths; mass grows with k³ but part strength only with k², so at k = 2 parts are about 8× heavier and 4× stronger: check pins and thin links when scaling up.
  • Notches: 90 degree V, 2.5 deep, 20 mm apart; detent nose offset 0.4 mm.
  • Slider 80 × 10 × 5 runs between rails with 0.4 mm gaps; the bowtie runs in a 12.8 mm guide.
  • Any small rubber band works; loop it from post to post behind the bowtie's back.
  • Kit: the base plate carries 5 mm pins (parts have 5.4 mm bores, 0.2 mm per side); every part prints flat on its own, and the assembled file shows them in place with 0.2 mm gaps, each part its own solid.

3D printable rubber-band bowtie detent slider: three-position snap… size chart

filewhatoverall mm
bowtie-slider-assembledassembled: 3 parts in place100 × 40 × 12.2
bowtie-slider-basebowtie slider base100 × 40 × 11.2
bowtie-slider-barbowtie slider bar80 × 10 × 9
bowtie-detentbowtie slider detent12 × 13.934 × 5

Mating features

Drawn at the exact size. Open press, slide, run and socket features by your process's clearance (tolerances by process); leave designed gaps and clamp fits as drawn.

featureexactmates withfitfiles
slider in rails10 wide, 0.4 gap each sidebase railsrunbar*
detent nose90 degree V, 0.4 offsetslider notchdesigneddetent*

Where the files are

Other publishers' files are linked, not hosted. "verify" = check the license at the link before commercial use.

WikipediaDetentwebPublisher's page; dimensions are facts
WikipediaRubber bandwebPublisher's page; dimensions are facts

Free files

★ Free files 4 parts. Xem Studio design: free to use, print and sell things from; not to be republished as files. Xem Studio Design License. index.json

Use this part in your AI. Your AI gets the exact sizes and files straight from Xem and can design a mount, case or adapter around it. Direct downloads here are limited to one file every 10 minutes; through your AI they are unlimited.

Connect Xem to your AI (free, no account, about a minute)
https://xemstudio.com/mcp
  1. Claude: Add to Claude
  2. ChatGPT (Plus or higher): open Connectors → Advanced → turn on Developer mode → Create → paste the address, no authentication → Create.
  3. Cursor: install with one click. VS Code: install with one click.
Other apps and full steps
bowtie-slider-assembledbowtie slider assemblySTEP · STL
bowtie-slider-basebowtie slider baseSTEP · STL
bowtie-slider-barbowtie slider barSTEP · STL
bowtie-detentbowtie slider detentSTEP · STL
Let your AI pull this. Claude: add Xem in one click. ChatGPT, Cursor or any MCP client: add https://xemstudio.com/mcp (free, no account). Your AI can then look up exact sizes, mating fits and free STEP/STL from every chat.
Set it up →

Plain text: sheet.txt · JSON: /api/geometry?object=rubber-band-bowtie-detent-slider

3D printable rubber-band bowtie detent slider: three-position snap slider (STL, STEP), isometric render of a generated part
Render of bowtie-slider-assembled from the free STEP; not to scale.

Fits with

Questions

How many stops?

Three, 20 mm apart.

Can I add more?

Yes: add more V notches to the bar at any spacing over 6 mm.

What sets the click force?

The rubber band tension.